AN Hose End Series Explained: Which Aeroflow Ends Suit Yo... 5 min read
AN Fittings

AN Hose End Series Explained: Which Aeroflow Ends Suit Your Hose

The series number tells you how a hose end seals and which hose it suits. Here's the full breakdown in four simple groups.

AN hose end fittings in different series with braided hose

Aeroflow makes hose ends in a string of numbered series, and the number tells you how the fitting seals and which hose it suits. Pick the wrong family and the end won't seal on your hose. The four groups below cover every family Aeroflow makes.

The four sealing styles

Every Aeroflow hose end uses one of four ways to grip and seal the hose:

  • Taper ends draw the hose onto a tapered tube as you tighten. Traditional and easy to align.
  • Cutter ends use a billet cutter that separates the wire braid and seals the hose twice for strong retention.
  • Push-lock ends have a barbed body. You push the hose on by hand, with no clamps and no tools.
  • PTFE ends use a purpose-built olive that compresses into a PTFE liner for a leak-free seal.

Series at a glance

Series Style Suits this hose Notes
100 Taper Stainless-braid Easy alignment
150 Full-flow taper Stainless-braid Larger bore
500 Cutter Stainless-braid Double seal
550 Full-flow cutter Stainless-braid Maximum retention
880 ELITE Cutter Stainless-braid Show finish, no hand polishing
200 PTFE PTFE-lined Fuel, oil, brake, E85
570 Full-flow PTFE PTFE-lined Larger bore
590 Dual PTFE PTFE-lined Tight-radius runs
400 Push-lock Push-lock No tools
510 Full-flow push-lock Push-lock Larger bore
Kryptalon Swivel Kryptalon kevlar Lightest, racing

Match the end to your hose

  • Braided stainless hose takes taper or cutter ends: 100 and 150 taper, 500 and 550 cutter, or the 880 ELITE cutter for a show finish.
  • PTFE hose takes PTFE ends: 200, the full-flow 570, or the 590 dual end for tight-radius runs.
  • Push-lock hose takes push-lock ends: 400, or the full-flow 510.
  • Kryptalon kevlar hose takes the matching Kryptalon swivel ends.

The word "full flow" means a larger internal bore for less restriction, which matters on bigger fuel and oil lines. Forged male taper ends thread straight into a female port without an adapter, and ORB to AN ends do the same for a PTFE line into an ORB port.

Which Aeroflow parts

Browse the full hose ends range, or jump to 200 Series PTFE, 100 Series taper, 400 Series push-lock or Kryptalon ends. Match them to the right hose.

Related guides

FAQ

Can I mix series on one hose?

No. Both ends must come from a family that suits your hose construction. A PTFE end won't seal on braided rubber hose, and a cutter end won't seal a PTFE line.

What does full flow actually change?

A full-flow end opens up the internal bore so the fitting flows closer to the hose itself. It helps most on larger fuel and oil lines where restriction costs you.

Are the ends reusable?

Taper, cutter and Kryptalon ends are designed to be reusable, so you can rebuild a hose after a trial fit. Always check the seal on reassembly.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Automotive AN bulkhead fittings with lock-nuts through a firewall panelAN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

Everything Aeroflow Jun 02, 2026