How to Assemble a PTFE AN Hose: Workshop-Floor Walkthrough 5 min read
Hose & Fittings

How to Assemble a PTFE AN Hose: Workshop-Floor Walkthrough

Build a PTFE braided AN hose end the right way once. Tools, the six-step assembly, the tightening rule, and the mistakes that cause leaks 200 km later.

Partially-assembled AN hose end fitting being attached to braided hose, vice jaws gripping, on a white studio background.
TL;DR: Cut square, mark insertion depth, push the socket on first, then thread the fitting in. PTFE-specific cutter-style hose ends bite into the liner. Don't substitute convoluted hose ends. Plan one fitting per 5 minutes once you're practised.

If you've never built an AN hose, the first one takes 20 minutes. The fifth takes three. The trick is doing it the right way once, not the wrong way fast.

This is a PTFE-specific walkthrough. Rubber-lined hose uses similar tools but different hose ends. Stick with one or the other inside a single hose.

Tools you need

  • Aluminium vice jaws. They protect anodised fittings from getting chewed by steel vice teeth. Cheap, essential.
  • PTFE-rated hose cutter. A rotating wheel cutter for clean square ends. Hacksaw works in a pinch but frays the braid.
  • Cutter-style PTFE hose end. Matched to your hose size. Aeroflow 500/550/880 series for PTFE.
  • Spanners. Open-ended in your AN sizes. Aluminium-coloured AN spanners stop fitting bite marks.
  • Marker pen. For the insertion depth line.
  • Light oil or PTFE assembly lube. Not engine oil. PTFE assembly lube is silicone or food-grade. A drop on the threads, nothing on the liner.

The six-step assembly

1. Cut square

Mark the hose where you want to cut. Use the cutter. Clamp the hose, slowly squeeze, rotate the cutter wheel around. Square cut every time.

Hacksaw is acceptable if you wrap masking tape around the cut zone first (stops braid fraying), but the cut quality matters. A ragged cut won't seat properly.

2. Trim the braid back (if needed)

Some PTFE hose ends use a "smooth bore" design where the braid sits between the socket and the nipple. Others bite the braid directly. Check your fitting's instruction sheet.

For Aeroflow 500-series PTFE cutter hose ends: the braid stays full length. No trimming needed.

3. Mark insertion depth

Slip the socket onto the hose first. Mark on the hose where the socket's leading edge reaches. This is your check-mark. If the hose backs out during assembly, you'll see it.

4. Push the socket on

Socket goes on the hose end-first. Open end faces the cut. Push it back from the cut so you have working room, usually about 30mm.

5. Insert the nipple (fitting)

Place the hose-end body in your aluminium vice jaws, nipple end up. Hose into the nipple. Push by hand as far as it will go.

The nipple has a sharp internal edge ("cutter") that bites into the PTFE liner. This is the seal. Don't push past the marked depth.

6. Thread the socket onto the nipple

Slide the socket up over the nipple. Spin it down by hand until threads engage. Spanner-tighten, firm, not gorilla. Final tightening: keep going until a small, even witness gap remains between the socket and the hose-end body, per Aeroflow's assembly instructions. The gap is your done signal, not a turn count.

Check the hose insertion depth mark hasn't moved. If it backed out: loosen, re-seat, re-thread.

The tightening rule

PTFE cutter hose ends use a precision interference fit. Over-tightening doesn't make it sealed. It just deforms the cutter and damages the seal.

The torque spec is "firm, by feel, not stupid." The fitting will tell you when it's done. If you're standing on the spanner, you're past it.

→ See hose tools + vice jaws

Common assembly mistakes

Mixing PTFE hose with rubber hose ends. PTFE has a smooth, hard liner. Convoluted (rubber-lined) hose ends are designed to bite into soft rubber and won't seal on Teflon.

Forgetting the socket. Pushing the nipple in first, then realising the socket is supposed to be on the hose. Now you have to back the nipple out and start over.

Cutting too short. Always cut long, fit the ends, trim if you need to. Five-millimetre too long is a one-minute fix. Five-millimetre too short is a new hose.

No vice jaws. Steel vice teeth chew anodised fittings. Looks ugly. Voids the visual warranty. Use aluminium jaws.

Skipping the assembly lube on the threads. Cutter hose ends use a precision threaded compression. Dry threads gall, especially on alloy. One drop of silicone lube on the threads.

What we stock for this

You'll do this once and want to do it again. It's that satisfying.

Shop Hose Assembly Tools → Vice jaws, cutters, sockets. Genuine Aeroflow tools. Ships overnight from Palmerston North.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Automotive AN bulkhead fittings with lock-nuts through a firewall panelAN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

Everything Aeroflow Jun 02, 2026