AN Fitting Sizes Explained: The NZ Builder's Thread C... 5 min read
an-fittings

AN Fitting Sizes Explained: The NZ Builder's Thread Chart

AN sizes match hose inside diameter, not OD. -6 = 3/8", -8 = 1/2", -10 = 5/8". The NZ builder's thread chart: sizing rules, common mistakes, and which fitting fits what.

Fanned-out arrangement of anodised aluminium AN fittings in multiple sizes on a white studio background.
TL;DR: AN sizes match hose ID (inside diameter), not outside diameter. -6 = 3/8", -8 = 1/2", -10 = 5/8". Most NA fuel feeds run -6. High-HP and E85 step up one size.

Bought a -6 fitting and the hose is -8? You're not the first.

AN sizing trips up everyone once. The numbers don't match anything you can measure with a tape. They're a legacy military spec inherited by motorsport in the 1950s and never updated. Here's the actual rule so you stop guessing.

What "AN" actually means

AN stands for Army-Navy. It's a US military thread and sleeve spec from WWII, adopted wholesale by hot-rod and racing builders because the seals are reusable, leak-free, and consistent across every brand that builds to spec.

The number after the dash isn't inches or millimetres.

It's a sixteenth-of-an-inch measure of the hose inside diameter the fitting was designed for. -6 means "designed for hose with a 6/16-inch (3/8") ID". -8 means "designed for 8/16-inch (1/2") ID hose".

That's it. That's the whole code.

The AN size chart

AN size Hose ID Metric ID Male thread Typical use
-3 3/16" 4.8 mm 3/8-24 Brake lines, gauge lines, vacuum
-4 1/4" 6.4 mm 7/16-20 Brake, clutch, return
-6 3/8" 9.5 mm 9/16-18 NA fuel feed, oil
-8 1/2" 12.7 mm 3/4-16 Turbo fuel feed, E85
-10 5/8" 15.9 mm 7/8-14 High-HP fuel, oil cooler
-12 3/4" 19.1 mm 1 1/16-12 Sump scavenge, breather
-16 1" 25.4 mm 1 5/16-12 Race dry-sump, big breather
-20 1 1/4" 31.8 mm 1 5/8-12 Top-fuel, methanol systems

→ Browse the full AN range

How to pick the right size for your build

Three rules. They cover 95% of NZ street and motorsport builds.

Rule 1: hose ID matches AN number. Order -6 hose, you need -6 hose ends. Mix them and you'll either crush the hose or have it slip.

Rule 2: feed bigger than return. Fuel return lines can be one size smaller than feed. The return still carries close to full pump volume, but at near-zero pressure, so the smaller line doesn't choke it. Common pairings: -6 feed with -4 return on naturally-aspirated. -8 feed with -6 return on boost.

Rule 3: E85 demands one size up. Ethanol is less energy-dense than petrol. You need more volume to make the same horsepower. A pump-gas build calling for -6 wants -8 on E85.

Common sizing mistakes

The four that cost workshops the most rework.

Sizing by outside diameter. A -8 fitting's male thread is roughly 3/4". That's the thread spec, not the hose ID. Always size by the hose.

Mixing brands inside one line. Quality brands all build to AN spec, but margins vary. Stick to one brand of fitting and hose inside any single line for a clean seal.

Stepping down between pump and regulator. A -6 feed into a -8 regulator inlet works fine. Going -8 down to -6 between the pump and the regulator creates a flow choke at exactly the wrong spot.

Banjo confusion. Banjo bolts use a separate metric or imperial thread spec (often M10×1.0, M12×1.25, or 7/16-20), not AN. They mate via banjo washers, not flares. Don't put a banjo bolt where an AN fitting belongs.

→ Need a thread adapter? See the adapter range

What we stock for this

You're not the first builder to second-guess AN sizing. Most workshops keep this chart pinned to the wall.

Shop AN Fittings → 1,037 genuine Aeroflow fittings in stock. Ships overnight from Palmerston North.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Automotive AN bulkhead fittings with lock-nuts through a firewall panelAN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

Everything Aeroflow Jun 02, 2026