Technical Information

Sizing charts, hose & fitting specifications, oil filter data, and the maintenance protocols our team uses on every build.

01 · Identification

Fitting size charts

Use the line drawings below to identify a fitting you already have on the bench. Print the chart to true size (no scaling), then lay the fitting on top to compare. The thread profile and diameter will line up with the matching drawing.

Male NPT identification

NPT (National Pipe Tapered) threads are the standard for ports on engine blocks, oil pans, intake manifolds and most accessory housings. The taper provides the seal, so thread sealant or PTFE tape is required.

Male NPT thread identification chart showing 1/8 inch through 1 inch NPT thread sizes

Common male NPT sizes: 1/8", 1/4", 3/8", 1/2", 3/4", 1".

Male AN / ORB identification

AN (Army-Navy) and ORB (O-Ring Boss) threads share the same outside diameter for a given dash size, but they seal completely differently. AN uses the 37° flare on the fitting nose; ORB uses a captive O-ring seated in a straight thread port. Don't interchange them.

Male AN and ORB adapter thread identification chart

AN dash sizes map to the same straight thread diameter as ORB, but the seal mechanism is different.

AN hex OD identification

The wrench flats on AN fittings, hose ends and adapters follow the SAE spanner sizes. Use this chart to identify the dash size from the hex across-flats measurement when the fitting itself isn't marked.

AN hex OD identification chart with SAE spanner equivalents

Numbers shown are the SAE spanner-size equivalent of each AN dash.

Fitting size cross-reference

Quick lookup between AN dash sizes, inch fractions and millimetres for hose ID, fitting OD and common port sizes.

Fitting and hose size cross-reference chart

02 · Hose

Hose specifications

Aeroflow Performance hose is engineered for hard automotive use: fuel, oil, coolant, brake, transmission, nitrous and air. Match the hose series to your fluid, pressure and temperature requirements using the cards below.

100 Series: Stainless steel braided

Aeroflow's most popular racing hose.

  • Double-braided 308 stainless steel outer for abrasion resistance
  • Smooth-bore CPE (Chlorinated Polyethylene) synthetic rubber inner liner
  • Optional gloss-black electroplated finish
  • Pressure: 1,000 PSI working (sizes -4 to -12)
  • Temperature: -40 °C to +150 °C
  • Use an inner coil spring for vacuum applications

Applications: Fuel, oil, coolant, air.
Compatible ends: 100, 150, 500, 550 & 880 Series reusable.

450 Series: Nylon braided

Up to 40 % lighter than stainless braid.

  • Braided nylon outer shield for abrasion resistance
  • Flexible 308 stainless inner core embedded into the liner for strength
  • Smooth-bore CPE synthetic rubber inner liner
  • Pressure: 1,000 PSI working (sizes -4 to -12)
  • Temperature: -40 °C to +150 °C
  • Use an inner coil spring for vacuum applications

Applications: Fuel, oil, coolant, air.
Compatible ends: 100, 150, 500, 550 & 880 Series reusable.

400 Series: Push-lock

Easy assembly with the matching push-lock hose ends.

  • Nylon-reinforced blue or black outer cover
  • Smooth-bore CPE synthetic rubber inner liner
  • Clamps required for all pressure applications
  • Temperature: -40 °C to +100 °C
  • Available -4 through -12
  • Use an inner coil spring for vacuum applications

Applications: Fuel, oil, coolant, air.
Compatible ends: 400 & 510 Series reusable push-lock.

500 Series: High-temp push-lock

Higher temperature ceiling and PS / trans-cooler approved.

  • Textured CPE synthetic rubber outer liner
  • Nylon-reinforced inner layer
  • Clamps required for high-pressure applications
  • Pressure: 290 PSI working (20 bar)
  • Temperature: -40 °C to +125 °C
  • Available -6 through -10

Applications: Fuel, oil, coolant, air, power steering, transmission cooler lines.
Compatible ends: 400 & 510 Series reusable push-lock.

200 Series: PTFE / stainless braid

High-pressure, leak-proof, recommended for E85.

  • 308 stainless outer braid (optional gloss-black electroplated)
  • Smooth-bore PTFE (Teflon) inner liner that resists fume permeation and fuel attack
  • Pressure: up to 4,000 PSI (1,000 PSI in -20 size)
  • Temperature: -70 °C to +250 °C
  • Excellent vacuum performance; use inner coil for high vacuum

Applications: Off-road brake, transmission, clutch, gauge, N2O, power steering, hydraulic, fuel, oil, coolant, air.
Compatible ends: 200 & 570 Series reusable.

250 Series: PTFE / black nylon braid

PTFE liner with a lighter nylon outer.

  • Black nylon outer braid, reinforced with an inner 308 stainless layer
  • Smooth-bore PTFE inner liner
  • Pressure: up to 4,000 PSI (1,000 PSI in -20 size)
  • Temperature: -70 °C to +200 °C
  • Excellent vacuum performance; use inner coil for high vacuum

Applications: Off-road brake, clutch, gauge, N2O, power steering, hydraulic, fuel, oil, coolant, air.
Compatible ends: 200 & 570 Series reusable.

Kryptalon® Big-bore Kevlar

The most flexible PTFE-lined hose Aeroflow makes.

  • Larger bore than regular AN hose for greater flow per dash size
  • Ultra-flexible convoluted outer with smooth-bore PTFE inner liner
  • Flame-retardant Kevlar braided outer cover
  • No special tools required; assemble with Aeroflow adjustable alloy wrenches
  • Temperature: -70 °C to +260 °C
  • Excellent vacuum performance; use inner coil for high vacuum

Applications: Off-road brake, transmission, clutch, gauge, N2O, power steering, hydraulic, fuel, nitromethane, oil, coolant, air.
Compatible ends: Kryptalon® Series reusable.

03 · Hose ends

Hose end specifications

Every Aeroflow hose end is machined from 6061 T-6 aluminium and finished to meet or exceed AN aerospace minimums. The cone seat is JIC 37° with a double Viton O-ring so the swivel rotates a full 360° under torque and still seals leak-free. Blue and black finishes are hard-anodised for wear, corrosion and colour retention. Stainless-steel lock-wire pins are included on every end.

100 Series Taper

Brazed full-flow hose end with a taper-design olive that compresses the hose into a purpose-cut socket for a leak-free seal. All angles are mandrel bent to keep flow paths smooth, and the swivel head rotates 360° for installation alignment.

  • Suitable for fuel, cooling, vacuum and oil systems
  • Not recommended for power steering or automatic-transmission lines
  • Hard-anodised (excluding silver)

Compatible hose: 100 Series stainless braid · 450 Series lightweight nylon braid.

150 Series Full-Flow Taper

The 150 is the CNC-machined one-piece version of the 100, with a heavier wall, a tighter mandrel-bent radius and an uninterrupted bore. Suited to fuel, coolant, vacuum and oil.

  • One-piece CNC machined construction
  • Not for power steering or automatic transmission
  • Hard-anodised (excluding silver)

Compatible hose: 100 Series stainless braid · 450 Series lightweight nylon braid.

500 Series Cutter

Brazed full-flow design with a billet cutter end that splits the outer braid and seals against the inner liner. This gives a second sealing surface for added retention and easier assembly. Swivel head for fitment flexibility.

  • Suitable for fuel, cooling, vacuum and oil systems
  • Not for power steering or automatic transmission
  • Hard-anodised (excluding silver)

Compatible hose: 100 Series stainless braid · 450 Series lightweight nylon braid.

550 Series Full-Flow Cutter

The CNC one-piece sibling of the 500. Same billet cutter sealing advantage with a tighter mandrel-bent radius and a thicker wall. Suited to fuel, coolant, vacuum and oil.

  • One-piece CNC machined construction
  • Not for power steering or automatic transmission
  • Hard-anodised (excluding silver)

Compatible hose: 100 Series stainless braid · 450 Series lightweight nylon braid.

400 Series Push-Lock

Brazed mandrel-bent body with a barbed end for tool-free push-on assembly. Comes with a finishing cover that hides the cut end of the hose for a clean install every time. Clamps required in all applications.

  • Not for power steering or automatic transmission
  • Hard-anodised (excluding silver)

Compatible hose: 400 Series push-lock hose (Blue / Black).

510 Series Full-Flow Push-Lock

One-piece CNC version of the 400 with a tighter mandrel-bent radius and thicker wall section. Same purpose-designed finishing cover for a professional look. Clamps required in all applications.

  • One-piece CNC machined construction
  • Not for power steering or automatic transmission
  • Hard-anodised (excluding silver)

Compatible hose: 400 Series push-lock hose (Blue / Black).

200 Series PTFE

Brazed full-flow end with a purpose-designed olive that compresses into the PTFE (Teflon®) inner tube for an easy, leak-free seal. All angles are mandrel bent. Swivel head rotates 360°. Recommended for E85.

  • Suits power steering, automatic transmission, nitrous, fuel, cooling, vacuum, oil, brake and clutch lines
  • Hard-anodised (excluding silver)

Compatible hose: 200 & 250 Series PTFE / stainless hose.

570 Series Full-Flow PTFE

One-piece CNC version of the 200. Same compression-olive seal into the PTFE liner, with a tighter mandrel-bent radius and a thicker wall. Rated for E85 and high-spec fluid systems.

  • One-piece CNC machined construction
  • Suits power steering, automatic transmission, nitrous, fuel, cooling, vacuum, oil, brake and clutch lines
  • Hard-anodised (excluding silver)

Compatible hose: 200 & 250 Series PTFE / stainless hose.

Kryptalon® Hose Ends

One-piece big-bore design with Aeroflow's patented compression-style olive. NHRA approved. Rated for E85, E10, methanol, nitro, oil, lubricants and coolant systems.

  • Designed exclusively for Kryptalon® large-bore lightweight hose
  • Hard-anodised
  • 360° swivel for easy alignment

Compatible hose: Kryptalon® hose only.

04 · Oil filtration

Oil filter information

Aeroflow oil filters use modern construction throughout: a coil-spring bypass design in place of the legacy leaf spring, CNC-machined threads for a precise mount, and a high-temp silicone anti-drain-back valve that prevents dry starts. The result is good filtration with minimal restriction so your engine sees consistent oil pressure under load.

Aeroflow oil filter range cutaway diagram
  • Heavy-duty back plate & housing resist pressure fatigue and surges in racing applications.
  • Fully-tucked double-seam base plate with hi-flow ports and Buna-N rubber gasket compatible with most racing fuels and lubricants.
  • 24 mm / 15/16" hex release nut with a lock-wire hole for tool-free removal and motorsport scrutineering.
  • Premium pleated synthetic-blend media delivers high flow with minimal pressure drop.
  • Louvred centre tube increases flow area and stops media wear from pleat movement.

Aeroflow Oil Filter Warranty

If an Aeroflow oil filter is ever found to be faulty in material or workmanship, we'll replace it free of charge. In the unlikely event of engine damage directly caused by a defective Aeroflow filter that was professionally installed and serviced per the engine manufacturer's intervals, Aeroflow will repair the damaged engine back to the state it was in immediately prior to the damage.

Claims must be lodged within 30 days of discovering the damage. Aeroflow reserves the right to inspect the engine and filter to determine the cause and extent. Engine-manufacturer warranties remain in effect when Aeroflow oil filters are used.

What the warranty does not cover:

  • Labour, towing or other external charges
  • Filters that have been subject to intentional misuse, neglect, negligence or damage
  • Filters improperly installed, maintained or operated
  • Filters installed against the published Aeroflow catalogue vehicle listings or manufacturer recommendations
  • Any failure caused by an external factor outside of Aeroflow's control

05 · Maintenance

Hose maintenance & inspection

Hose assemblies in service should be inspected on a regular schedule for leaks, corrosion, abrasion, kinks and any other signs of wear. Replace any worn or damaged assembly immediately. Don't wait for a failure on track.

Cleaning

Blow assemblies out with compressed air. If the hose is oil- compatible, rinse with turpentine. Otherwise rinse with warm water, being careful not to exceed the hose's maximum temperature rating.

Inspection

Examine the hose-end internals for cut or bulged tube, debris or obstruction. On compression fittings, confirm the socket-nut-to-hex gap is correct (check our hose-end assembly videos if you're not sure). On swivels, the nut should rotate freely. Watch the lay line on the hose to confirm the assembly isn't twisted. Cap finished assemblies with plastic covers for storage.

Hydrostatic pressure testing

Hose-end assemblies should be hydrostatically tested at twice their recommended working pressure. Hold test pressure for at least 30 seconds and no more than 60 seconds. While under test pressure, visually inspect for leaks, weakness, or any movement of the end relative to the hose. Any of these is cause for rejection.

Caution. Hydrostatic testing should be performed by trained personnel in an approved environment, behind appropriate barriers to protect the operator.

06 · Service life

Service-life factors

Every hose assembly has a service life. How long yours lasts depends on the variables below. Plan and route the install with all of them in mind.

Bend radius

The minimum bend radius is rated at maximum operating pressure with no flex. Bending tighter than the minimum reduces safe pressure and shortens hose life.

Vacuum service

For -12 hoses and larger under significant vacuum, an internal coil support spring is required to prevent collapse.

Operating pressure

Aeroflow assemblies are rated for continuous operation at the hose's specified maximum. Typically operating pressure equals one-quarter of the burst pressure.

Burst pressure

Burst figures are test values. They apply only to assemblies that haven't been in service or assembled for more than four weeks.

Pressure surges

Surges in hydraulic systems can exceed the hose's working pressure and shorten life, and they often don't register on mechanical gauges. If surges are severe, step up to a hose with a higher working pressure.

High pressure

Treat anything above 250 PSI as hazardous. Route and secure lines to prevent whiplash in the event of a failure, and shield them from external impact and chemical attack.

Ambient temperature

Extreme outside temperatures affect cover strength and structure. Combined with fluid temperature inside, ambient heat is one of the biggest factors in hose life. Aeroflow has insulation solutions, so talk to the tech team for recommendations.

Operating temperature

The temperature ratings in our specs reflect typical heat ranges for each application. Continuous operation at or near the maximum shortens life. If heat is a concern, choose a PTFE-lined hose or a hard line that's rated for the duty.

Chemical resistance

Cleaning chemicals around the hose end and cover can degrade O-rings, anodised finishes and the rubber outer. Be deliberate about what hits your fittings.

07 · Fuel & safety

Important fuel & safety notes

Hose assembly inspection

Inspect every hose assembly on a regular schedule. Look for leaks, corrosion, abrasion, kinks or any other sign of wear. Replace any worn or damaged assembly immediately.

Fuel injection: recirculating systems

Every hose in the Aeroflow range is suitable for leaded and unleaded fuel. However, in fuel-injection systems that recirculate fuel, the fuel oxidises over time and can attack the hose's inner liner. Keep exposure to oxidised fuel to a minimum: drain and flush the fuel system with fresh fuel periodically.

Methanol & ethanol

Every Aeroflow hose handles methanol and ethanol. But both fuels are extremely corrosive and hygroscopic (they absorb water from the air), so they'll attack the entire fuel system if it isn't flushed and prepared for storage correctly. Fuel additives and stabilisers help, but the best approach is to flush and store the system on unleaded.

08 · Downloads

Instructions & downloads

Product instruction sheets are added as we receive them from Aeroflow Australia. If you need a sheet that isn't here yet, get in touch and we'll send you the latest revision direct from the manufacturer.

Request an instruction sheet →

For the full Aeroflow Performance Products catalogue, visit aeroflowperformance.com.

Still not sure which hose, end or fitting suits your build? Send us your spec and we'll recommend the right combination, no guesswork.