PTFE vs Rubber Fuel Hose: Which Line Do You Actually Need? 5 min read
fuel-system

PTFE vs Rubber Fuel Hose: Which Line Do You Actually Need?

PTFE is chemically inert, so it is required for E85, methanol and brake fluid. Rubber-lined suits petrol, oil and water. The NZ guide to picking the right braided hose liner.

Two coils of automotive braided hose side by side — PTFE-lined on the left, rubber-lined on the right.
TL;DR: PTFE is Teflon-lined and chemically inert. Required for E85, methanol, brake fluid, and high-temp work. Rubber-lined is fine for petrol, oil, and water. Both come in -3 to -16.

You can run E85 through a rubber-lined hose. For about three months. Then it starts shedding into your fuel rail.

PTFE vs rubber isn't a price comparison. It's a chemistry question. Here's when each one is the right call.

What's actually inside the hose

Braided hose has two layers: the liner (the bit the fluid touches) and the braid (the woven outer that holds pressure).

The braid is almost always stainless steel or coated steel. It's the liner that matters.

PTFE (Teflon) is chemically inert. It doesn't swell, doesn't react with ethanol or methanol, handles temperatures from -50°C to over 200°C, and resists the aromatic hydrocarbons in pump petrol that slowly turn rubber to mush.

Nitrile / CPE rubber is the workhorse liner. Petrol-rated, oil-rated, cheap, easy to assemble, and well-proven. But it swells in ethanol, breaks down in methanol, and doesn't like brake fluid.

When to use which

Fluid PTFE Rubber-lined Notes
91/95/98 petrol OK OK Either works. Rubber cheaper.
E85 (any blend) Required Avoid Ethanol destroys nitrile lining.
Methanol Required No Even faster than E85.
Engine oil OK OK Rubber fine to ~150°C.
Transmission fluid OK OK Either works.
Brake fluid (DOT 3/4) Required No Glycol attacks rubber.
Brake fluid (DOT 5) OK OK Silicone, both fine.
Coolant / water OK OK Either works.
Fuel return (low pressure) OK OK Match the feed.

→ See all hose options

The three real differences

Bend radius. PTFE has a larger minimum bend radius than rubber, and it's less forgiving. Kink a PTFE line once and the liner cracks. Rubber tolerates being abused on installation. Plan PTFE runs more carefully.

Hose-end compatibility. PTFE needs PTFE-specific hose ends. They seal by compressing an olive (ferrule) over the liner. Rubber braided hose uses the classic taper-style cutter socket that bites into the rubber liner. Don't cross them.

Cost. PTFE is 2-3× the price of equivalent rubber-lined per metre. On a brake or short fuel run, the cost diff is nothing. On a 5-metre dry-sump scavenge line, it adds up. And you don't need PTFE for that.

NZ-specific call: E85 availability

Pump E85 is gone in NZ. Gull pulled it back in 2020, and nothing replaced it at the forecourt. If you're running E85 here now, it's coming out of a drum from a race-fuel supplier. That's a deliberate build choice, and it commits you to PTFE lines from day one, or you're rebuilding the fuel system every season.

Even if you're "just running E40 on tune-up days". The ethanol concentration alone is enough to start attacking nitrile. The fix once it starts isn't cleaning, it's replacing the hose.

Build it right the first time.

Common hose mistakes

Buying the most basic hose and the most expensive fittings. Hose ends are reusable across rebuilds. Hose isn't. Spend the money on the liner spec, not the bling on the ends.

Sizing by the braid OD. AN size = hose inside diameter = the liner ID. -8 PTFE and -8 rubber-lined are the same size on the fitting end. Different OD on the braid. But the fitting doesn't care.

Mixing PTFE hose with rubber-style hose ends. PTFE hose has a smooth, hard, slippery liner. Taper-style rubber hose ends are designed to bite into soft rubber. Wrong combo = a leak, usually within the first few drives.

What we stock for this

PTFE for fuel, brake, methanol. Rubber for water, oil, return. Sized by liner ID.

Shop Braided Hose → Genuine Aeroflow braided hose, PTFE and rubber, -3 to -16. Ships overnight from Palmerston North.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Automotive AN bulkhead fittings with lock-nuts through a firewall panelAN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

Everything Aeroflow Jun 02, 2026