Bulkhead Fittings: Running AN Lines Through a Firewall or... 5 min read
AN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

How AN bulkhead fittings pass a line cleanly through a firewall, fuel cell or panel, and what you need to do it.

Automotive AN bulkhead fittings with lock-nuts through a firewall panel

When a fuel, oil or coolant line has to cross a firewall, a fuel-cell wall or a floor panel, you don't just drill a hole and feed the hose through. A bulkhead fitting passes the line through cleanly, clamps and supports it at the panel, and protects the hose from a sharp edge. The seal is made at the flare connections, not at the panel itself.

How a bulkhead fitting works

The fitting has a long threaded body that passes through a hole in the panel. A bulkhead nut threads on behind the panel and clamps the fitting in place. You land an AN hose end or an adapter on each side, so the line is continuous but the panel carries no load on the hose and the hose never rubs on a raw edge.

What you need

  • The bulkhead fitting in your AN size.
  • A bulkhead nut, sometimes called a jam nut, to lock it to the panel.
  • An AN hose end or adapter for each side.

Fitting one, step by step

  1. Drill the panel to the size the fitting specifies, and deburr the hole.
  2. Pass the threaded body through and start the bulkhead nut on the back.
  3. Set the orientation you want, then tighten the nut to clamp the fitting to the panel.
  4. Land your hose end or adapter on each side and check both seals.

Choosing the AN size

Match the bulkhead to the line it carries. A fuel feed and return each get their own bulkhead in the matching AN size, sized the same way as the rest of that run. If you're unsure, the AN size chart below walks through it.

Where bulkheads earn their keep

Fuel cells use them to bring feed and return through the wall without a leak path. Firewalls use them to pass fuel, oil or brake lines into the cabin or engine bay tidily. Boot floors and chassis panels use them anywhere a line would otherwise rub on a raw edge. They also double as a neat union when you want to anchor a join to a panel.

Bulkhead or grommet?

A rubber grommet only protects the hose from the edge. A bulkhead fitting does that and seals the panel and supports the line, which is what you want on a fuel cell or a firewall. Use a grommet only where there is nothing to seal and no pressure.

Which Aeroflow parts

Browse bulkhead fittings and the wider fittings range, then pick the matching hose ends.

Related guides

FAQ

How does the panel seal?

The bulkhead nut clamps the fitting to the panel and supports the line; the fitting doesn't seal the panel hole itself. The seal is made at the flare connections on each side. On a fuel cell, use the nut and sealing washer specified for the cell.

Can I use a bulkhead as a union?

Yes. With a hose end on each side it joins two lines while anchoring the join to a panel, which keeps the run tidy and supported.

What size hole do I drill?

Drill to the size the fitting calls for in your AN size, then deburr so there is no sharp edge against the fitting.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Silicone hose shapes: elbow, reducer and hump joinerBuyer's Guide

Silicone Hose Shapes Explained: Elbows, Reducers, Humps and More

Everything Aeroflow Jun 02, 2026