NPT, BSP, ORB, AN: The Thread Identification Cheat Sheet 5 min read
adapters

NPT, BSP, ORB, AN: The Thread Identification Cheat Sheet

NPT tapers and seals on the thread. BSP seals on a washer. ORB uses an O-ring. AN is a 37° flare. How to tell four near-identical threads apart and pick the right adapter.

Flat-lay of automotive thread adapters — NPT, BSP, AN, and ORB — in brass and anodised aluminium on a white studio background.
TL;DR: NPT tapers and seals on the thread itself. BSP parallel and seals on a washer. ORB has an O-ring at the base. AN is 37° flare. Mix them wrong and you leak. Match them right and you walk away.

Pulled a thread you don't recognise off an old block? Welcome to the worst-kept secret in automotive plumbing.

There are four thread families you'll meet on any NZ build. Most look almost identical. They seal differently. Mix them up and you either crush an O-ring or leak fuel down your block.

The four thread families

NPT. National Pipe Thread (tapered). US standard. The threads themselves taper inward. Tightening forms the seal as the male wedges into the female. Always needs thread tape or sealant. The single most common port thread on US aftermarket parts.

BSP / BSPP. British Standard Pipe (parallel). Mostly UK / European. Same 55° thread angle as its tapered cousin BSPT, but parallel. It relies on a bonded washer or O-ring at the base to seal, NOT the threads. BSPT (PT / Rc) is the tapered version and seals on the thread like NPT. That one is the real JDM thread: Honda, Toyota, and Nissan block ports for oil pressure and temp senders are overwhelmingly 1/8-28 BSPT, not parallel BSPP.

ORB. O-Ring Boss (also called SAE straight-thread). Parallel thread with a defined chamfer at the base for an O-ring to sit in. Most modern Aeroflow regulators, surge tanks, and catch cans use ORB ports. Clean seal, reusable.

AN, Army-Navy. 37° flare seal. The "male" has a flared cone; the "female" has a matching seat. No tape, no washer, just metal-on-metal at the flare. The motorsport default.

The thread ID cheat sheet

Thread Angle Seal point How to identify Adapter you need
NPT 1/8" 60° Threads (tapered) Visibly tapered; ~10.3mm OD at tip NPT-to-AN
NPT 1/4" 60° Threads (tapered) Tapered; ~13.7mm OD at tip NPT-to-AN
BSPP 1/8" 55° Washer at base Parallel; ~9.7mm OD constant BSPP-to-AN
BSPP 1/4" 55° Washer at base Parallel; ~13.1mm OD constant BSPP-to-AN
BSPT 1/8" (PT / Rc) 55° Threads (tapered) Tapered like NPT but 28 TPI; the classic JDM sender port BSPT-to-AN
ORB -6 (9/16-18) 60° UN O-ring at chamfer Parallel + visible O-ring groove ORB-to-AN
ORB -8 (3/4-16) 60° UN O-ring at chamfer Parallel + O-ring groove ORB-to-AN
AN -6 (9/16-18) 37° flare Flared seat Same thread as ORB -6; LOOK FOR FLARE Direct AN-AN union

The trick: ORB and AN share the same thread spec. They're both 9/16-18 in size -6. But ORB seals at the base on an O-ring; AN seals at the tip on a flare. They are not interchangeable. Fit an AN union into an ORB port and you'll leak. The female ORB port has a smooth chamfered seat; an AN-flare male has a 37° cone that doesn't reach the O-ring groove.

→ Browse the full adapter range

The five-second visual check

You don't always have a thread gauge in your pocket. Three quick checks cover 90% of cases.

  1. Look down the side. Does the diameter shrink toward the tip? Tapered = NPT or BSPT (27 vs 28 TPI on the 1/8" size). Constant = BSPP, ORB, or AN.
  2. Look at the end face. Cone-shaped tip with a 37° angle? AN. Flat-ended with an O-ring groove just behind it? ORB. Plain flat-end with a parallel thread? BSP.
  3. Count the threads per inch. Most pocket calipers plus a printed TPI chart get you to a confident answer in 30 seconds. 18 TPI = -6 ORB or AN. 16 TPI = -8 ORB or AN. 27 TPI = NPT 1/8". 28 TPI = BSPT or BSPP 1/8".

Common identification mistakes

Confusing BSPP with NPT. Both look "British style" at first. The taper is the give-away. NPT visibly cones inward toward the tip. You can see it. BSPP is dead parallel.

Assuming AN = ORB. Same thread size, different seal. Screw an AN union into an ORB port and it will leak. Use an ORB-to-AN adapter. There's one for every size.

Banjo thread ≠ fitting thread. Banjo bolts use yet another spec (often M10×1.0 or 7/16-20). The thread on the bolt doesn't tell you anything about what hose end it pairs with. The banjo eye does.

What we stock for this

If in doubt, take the part to your local workshop and ask. Or email the photo to us. We ID threads daily.

Shop Thread Adapters → 662 adapters: NPT, BSP, ORB, AN, JIC, metric. Ships overnight from Palmerston North.

Keep reading

AN plumbing job: braided hose, fittings and toolsBuyer's Guide

Planning an AN Plumbing Job: Hose, Fittings and Tools

Everything Aeroflow Jun 02, 2026
Automotive banjo fittings and banjo boltsAN Fittings

Banjo Fittings and Bolts: Brake, Fuel and Turbo Oil Feeds

Everything Aeroflow Jun 02, 2026
Automotive AN bulkhead fittings with lock-nuts through a firewall panelAN Fittings

Bulkhead Fittings: Running AN Lines Through a Firewall or Tank

Everything Aeroflow Jun 02, 2026