Aeroflow AF6010-4000 Holden 304 Air Gap Dual Plane Non EFI Intake Manifold, Natural Cast Finish 1500 - 6500 RPM, Square Bore Carburettor Pad, Non-EGR
Aeroflow AF6010-4000 Holden 304 Air Gap Dual Plane Non EFI Intake Manifold, Natural Cast Finish 1500 - 6500 RPM, Square Bore Carburettor Pad, Non-EGR (view 2)
Aeroflow AF6010-4000 Holden 304 Air Gap Dual Plane Non EFI Intake Manifold, Natural Cast Finish 1500 - 6500 RPM, Square Bore Carburettor Pad, Non-EGR (view 3)

Aeroflow Holden 304 Air Gap Dual Plane Non EFI Intake Manifold, Natural Cast Finish 1500 - 6500 RPM, Square Bore Carburettor Pad, Non-EGR - AF6010-4000

Regular price$679.03
Pay in 4 interest-free payments of $169.76 with Afterpay
/
  • GST included
  • NZ-owned since 2003
Tax included. Shipping calculated at checkout.
Part No. AF6010-4000
  • Delivered NZ-wide
  • Available to order
  • Inventory on the way

  1. OrderedToday
  2. Shipped
  3. Delivered
Visa Mastercard American Express Apple Pay Google Pay Shop Pay Afterpay

Get the maximum power from your carburetted engine with this Air Gap Holden carburetted cast intake manifold. This dual-plane intake manifold is designed to keep your air and fuel distribution going into the engine at a steady and even flow for maximum performance and efficiency. The carburettor-mounting pad is designed to accept aftermarket square-bore carburettors with either manual or electric choke options available on today’s market. Specifically designed for Holden 304 V8 engines operating from idle to 5500 rpm range. In most cases, these manifolds accept late model water necks, air conditioning, alternator and H.E.I. ignition systems.

Intake Runners should be port matched to your cylinder heads for optimal performance.

• Fits Holden 304 V8 Engines. Will not suit early Holden 308 cylinder heads. This is designed for late model Holden VN Engine Models Non EFI models only. Use A6010-4003 for EFI applications.

•Dual Plane Configuration.

• RPM operating range - 1500 to 6500.

• Natural Cast Finish.

• Note: This can be used with both Holden V8 cylinder heads with modifications. New holes must be drilled out in intake manifold at the correct angle and correct location. These locations are marked on the intake manifold with pilot holes predrilled.

•This intake manifold includes a blank boss on each cylinder intake runner. This can be used for EFI applications with a fuel injector or a nitrous nozzle. Each boss must be drilled out and tapped to or welded to suit your application.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

We provide the best shipping service possible in New Zealand. Every order ships from our Palmerston North warehouse with tracked overnight delivery right to your doorstep.

Cost. Shipping costs are calculated at checkout based on your delivery address — the price you see is the price you pay. No sneaky hidden taxes or surprise import duties.

Delivery time. We aim to have your order with you within a week of placing it.

How we ship. All orders are shipped with DHL direct to our facility, then unpacked and dispatched the same day via a tracked overnight courier service across New Zealand.

Read our full shipping policy →

Every product we sell is genuine Aeroflow Performance stock — backed by Aeroflow's manufacturer warranty and our commitment to making it right.

Authenticity. Genuine Aeroflow Performance Products, sourced direct from Aeroflow Australia. No grey-market, no knock-offs.

Warranty. All Aeroflow products carry the manufacturer's standard warranty. Workmanship and materials are covered against defects from the date of purchase.

NZ Consumer Guarantees Act. You also have statutory rights under the New Zealand Consumer Guarantees Act — these always apply on top of any manufacturer warranty.

Returns. Because we special-order each item directly from Aeroflow Australia to keep prices competitive, we strongly recommend triple-checking that the part is correct for your application before ordering. Returns are accepted only if a product is sent incorrectly or has a warranty issue.

If you're unsure something will fit, just send us a message — we'd much rather help you order the right part first time.

Read our full refund policy →

We accept Visa, Mastercard, Amex, Apple Pay, Google Pay and Shop Pay through Shopify Payments.

You can also pay with Afterpay in 4 interest-free fortnightly payments.

All payments are encrypted and PCI-DSS compliant, so your card details never touch our servers.

Get the maximum power from your carburetted engine with this Air Gap Holden carburetted cast intake manifold. This dual-plane intake manifold is designed to keep your air and fuel distribution going into the engine at a steady and even flow for maximum performance and efficiency. The carburettor-mounting pad is designed to accept aftermarket square-bore carburettors with either manual or electric choke options available on today’s market. Specifically designed for Holden 304 V8 engines operating from idle to 5500 rpm range. In most cases, these manifolds accept late model water necks, air conditioning, alternator and H.E.I. ignition systems.

Intake Runners should be port matched to your cylinder heads for optimal performance.

• Fits Holden 304 V8 Engines. Will not suit early Holden 308 cylinder heads. This is designed for late model Holden VN Engine Models Non EFI models only. Use A6010-4003 for EFI applications.

•Dual Plane Configuration.

• RPM operating range - 1500 to 6500.

• Natural Cast Finish.

• Note: This can be used with both Holden V8 cylinder heads with modifications. New holes must be drilled out in intake manifold at the correct angle and correct location. These locations are marked on the intake manifold with pilot holes predrilled.

•This intake manifold includes a blank boss on each cylinder intake runner. This can be used for EFI applications with a fuel injector or a nitrous nozzle. Each boss must be drilled out and tapped to or welded to suit your application.

Genuine Aeroflow turbocharger, intercooler and wastegate with the Everything Aeroflow logo

Why Everything Aeroflow

Genuine parts. Fair prices. Honest lead times.

Aeroflow makes over 12,000 parts, and we bring every one in from Aeroflow Australia every Tuesday and Friday. Order by 10:30am Tuesday and your part is usually on the courier to you on Thursday. Order by 10:30am Friday and it leaves on Monday. The product page tells you which before you buy.

Buying little and often from Sydney is also why our prices are sharp. There is no bulk-import markup, so when Aeroflow runs a special it goes straight onto the site. Every order is tracked, in NZ dollars with GST included, and it is genuine Aeroflow, never a grey import.

Our story

Recently viewed